The short answer
A Brooklyn Heights chimney usually needs a new liner when the old clay tiles are cracked or deteriorated, or when the heating appliance changes, especially in an oil-to-gas boiler conversion. We inspect the flue first, then install a liner sized to the appliance it will serve.
Many homes in Brooklyn Heights are brownstones, rowhouses and pre-war apartment buildings. Their masonry chimneys were built long before today's boilers, water heaters and wood stoves. A flue liner is the protective channel inside the chimney. It carries exhaust up and out, and it keeps heat and corrosive byproducts away from the brick and mortar. When that liner is cracked, missing or the wrong size for the appliance, the chimney can't do its job safely. SummitHearth Chimney Services is based in Brooklyn, about a mile southeast of Brooklyn Heights. Our certified technicians inspect, size and install chimney liners for homes and buildings throughout the neighborhood.
Why Older Chimneys in Brooklyn Heights Need Attention
Many chimneys in the neighborhood's brownstones and rowhouses have clay tile liners, and some older flues have no liner at all. Over decades, freeze-thaw cycles, settling, and moisture can crack tiles and wear away the mortar joints between them. Gaps in a liner can let heat and combustion gases reach the surrounding masonry and wood framing. In a row of attached homes, a party wall may also be involved.
Usage matters too. Boilers in multi-unit pre-war buildings run hard through New York City's heat season, which lasts from October 1 through May 31. During those months owners have to keep apartments heated to the city's minimum temperatures. A chimney that runs for eight months of the year shows wear faster than one used for an occasional fire.

Oil-to-Gas Conversions and Liners
Fuel conversions are one of the most common reasons we install liners in Brooklyn Heights. When a New York City building converts its boiler from oil to gas, the chimney has to be evaluated as part of the work. A new liner is often needed. Gas exhaust produces acidic condensate, and that condensate can corrode a masonry flue that handled oil exhaust without trouble.
If you're planning a conversion, bring us in early. A flue inspection before the new boiler goes in shows whether the existing liner can stay or must be replaced. That gives your heating contractor and your schedule fewer surprises.
How We Approach a Liner Installation
Every job starts with an inspection. The NFPA 211 standard calls for chimneys, fireplaces and vents to be inspected once a year. Chimney professionals use three inspection levels. A Level 2 inspection applies when the system changes, such as a new appliance or a switch of fuel, or when the home is sold. Liner work usually falls in that category. A Level 3 inspection is used only when a hidden hazard can't be reached without opening part of the chimney or building.
From there, our process is straightforward:
- Camera inspection of the flue to document cracks, gaps and blockages
- Confirming which appliance or appliances the flue will serve, and their fuel type
- Sizing the liner to match the appliance's venting needs
- Selecting a liner type suited to the fuel and the chimney's shape
- Installing the liner with the appropriate connections, cap and insulation where needed
- A final check and a walkthrough of what was done
Time for your annual chimney check?
Choosing the Right Liner Type
There's no single liner that fits every chimney. Stainless steel liners are widely used for gas and oil appliances and for wood stoves. They can be flexible or rigid depending on how straight the flue runs, and many older Brooklyn Heights chimneys have offsets that favor a flexible liner. Cast-in-place liners form a new interior surface within the existing masonry and can be an option for some deteriorated flues. Replacement clay tile is sometimes possible but often impractical in an existing chimney. We explain the options that fit your chimney and appliance, and we tell you why we recommend one over another.
Serving Brooklyn Heights and Nearby Neighborhoods
We work with single-family homeowners, owners of multi-unit rowhouses, and boards of pre-war apartment buildings. Our office is close by, so we can coordinate inspections and installation visits around tenants and contractors. We also install chimney liners in Downtown Brooklyn, DUMBO, Boerum Hill, Fort Greene and Carroll Gardens.
More services in Brooklyn Heights
- Chimney Sweep in Brooklyn Heights
- Chimney Inspection in Brooklyn Heights
- Chimney Repair in Brooklyn Heights
- Air Duct Cleaning in Brooklyn Heights

