Skip to content
Serving Brooklyn and nearby cities Mon–Fri: 8 AM–8 PM · Requests accepted 24/7 · (730) 272-3310

Chimney Liner Installation in Park Slope, Brooklyn

Serving Park Slope and nearby cities. Tell us about the job and we’ll call you back to confirm the details.

Tell us what’s going on

Prefer to talk? (730) 272-3310

The short answer

Many Park Slope brownstones, rowhouses and pre-war buildings have old masonry flues that need a liner, especially after an oil-to-gas boiler conversion or a new appliance. SummitHearth inspects the chimney first, then installs a liner sized to your equipment so exhaust vents safely and the masonry is protected.

Many Park Slope homes were built long before modern heating equipment existed. Brownstones, rowhouses and pre-war apartment buildings often have original masonry flues that were never lined, or liners worn down by decades of use. A chimney liner protects the brick and mortar from heat and exhaust and helps your boiler, furnace, water heater or fireplace vent the way it should. SummitHearth installs chimney liners for homes and buildings in Park Slope (11217) and nearby neighborhoods. Every job starts with an inspection so the liner matches both the appliance and the flue it runs through.

Why Park Slope Chimneys Often Need a Liner

Older masonry chimneys in the neighborhood were usually designed for coal or wood. Over time, mortar joints erode, clay tiles crack, and some flues have no tile lining at all. In attached rowhouses, shared walls add another concern: a gap in a damaged flue can let heat or exhaust reach wood framing or a neighboring space.

Changing equipment is another common reason. A new, more efficient boiler or water heater may need a much smaller flue than the old one. When a flue is too large, exhaust cools before it leaves the chimney. That causes condensation inside the masonry and weak draft at the appliance.

  • Crumbling mortar or flakes of clay tile in the cleanout or firebox
  • White staining or damp spots on chimney walls inside the house
  • Weak draft, smoke spilling into the room, or a boiler that keeps shutting down
  • Rust or loose debris around the flue connector in the basement
Chimney Liner Installation at a home

Oil-to-Gas Conversions and Heat Season Timing

When a New York City building converts its boiler from oil to gas, the chimney has to be evaluated as part of the work. A new liner is often needed, because gas exhaust produces acidic condensate that can corrode a masonry flue from the inside. If your building is planning a conversion, schedule the chimney evaluation early. That way the liner work lines up with the boiler installation instead of holding it up.

Timing also matters because of the city's heat season, which runs from October 1 through May 31. During those months, building owners must keep apartments heated to the city's minimum temperatures. A liner job that takes the boiler offline needs careful planning in winter. Many owners choose to line the chimney in late spring or summer when the heat can be off without affecting tenants.

How We Install a Chimney Liner

The NFPA 211 standard calls for chimneys, fireplaces and vents to be inspected once a year. A Level 2 inspection is the appropriate level when the system changes, such as a new appliance or a switch of fuel, or when a home is sold. That inspection, which usually includes a camera look inside the flue, tells us what liner size and material your appliance needs.

Our certified technicians work from both the roof and the basement or fireplace. In attached rowhouses and apartment buildings, roof access often runs through a hatch or bulkhead, so we'll confirm access with you before the work day.

  • Inspect and measure the flue, and check the appliance's venting requirements
  • Clean the chimney so the liner can be installed through a clear passage
  • Install a liner sized to the appliance, most often stainless steel for gas and oil equipment
  • Connect the liner at the top and bottom, and fit a cap to keep out rain, debris and animals
  • Check the draft and walk you through what was done

Time for your annual chimney check?

Choosing the Right Liner for Your Home

Stainless steel liners are the most common choice for gas and oil appliances because they resist corrosion and can be sized closely to the equipment. Wood-burning fireplaces sometimes need a different approach, depending on the shape and condition of the flue. Size matters either way. A liner that is too large lets exhaust cool and condense, and one that is too small can keep the appliance from venting properly.

We explain what we found, show you photos where possible, and lay out the options in plain terms so you can decide what makes sense for your home.

Serving Park Slope and Nearby Neighborhoods

Park Slope is close to our Brooklyn office, which makes it easy to schedule an inspection and plan the work. We also install chimney liners in Prospect Heights, Carroll Gardens, Cobble Hill, Gowanus and Red Hook. Brownstones, rowhouses and pre-war buildings in those neighborhoods often face the same liner questions.

More services in Park Slope

Related

Chimney sweep cleaning a brick chimney on a rowhouse roof

Book Chimney Liner Installation in Park Slope

Serving Park Slope and nearby cities.

  • Diagnosis before any repair
  • Written price up front
  • Written price before we start

What to expect

How a visit goes

  1. We find the cause first

    A leak or a smoky fireplace can come from several places. We trace the problem to its source before suggesting a fix, so you are not paying for work that misses the real issue.

  2. We protect your home while we work

    We lay down drop cloths, seal off the fireplace opening and use containment when we clean, so soot and dust stay out of your living space.

  3. We explain it in plain language

    You will hear what we found, why it matters and what your options are, without jargon. If you have questions after we leave, we are glad to walk through the photos with you again.

FAQ

Common questions

How do I know if my Park Slope chimney needs a liner?

Common signs include crumbling mortar, tile fragments at the base of the flue, damp or stained chimney walls indoors, and draft problems. A new appliance or a fuel switch is also a good reason to check. An inspection with a camera is the reliable way to know.

Do I need a new liner if my building is switching from oil to gas?

Often, yes. When a New York City building converts its boiler from oil to gas, the chimney has to be evaluated, and a new liner is frequently needed because gas exhaust produces acidic condensate that can corrode a masonry flue.

When is the best time to install a liner?

Late spring and summer are usually easiest. New York City's heat season runs from October 1 through May 31, and owners must keep apartments heated during that time, so taking a boiler offline in winter needs extra planning.

What kind of inspection comes before liner installation?

The NFPA 211 standard describes a Level 2 inspection for system changes such as a new appliance or a switch of fuel, and when a home is sold. It typically includes a camera inspection of the flue.

Will you need access to my roof?

Yes. Liners are usually installed from the top of the chimney and connected at the bottom. In rowhouses and apartment buildings, we'll coordinate roof access through a hatch or bulkhead with you ahead of time.

Do you install liners outside Park Slope?

Yes. We also serve Prospect Heights, Carroll Gardens, Cobble Hill, Gowanus and Red Hook.

Not sure what your chimney or vents need?

Tell us what you're noticing, whether it's smoke, a leak, a smell or slow drying. We'll inspect, show you photos of what we find and give you a written price before any work begins.

Call (730) 272-3310 Request Service